Hey buddies! As plenty of y’all would possibly know, Ashley and I merely moved into our first office/studio space and now we’ve got been busy fixing her up! Considered one of many first points we knew we needed for this space was a espresso bar 😉 We constructed this large cute DIY Fancy Farmhouse Console for my dwelling, nonetheless we every decided it would make a really cute espresso bar, and that’s merely what we did with it! Sooner than I current it to you, check out the DIY YouTube video on how one can assemble it HERE or by clicking beneath!
Look how cute she turned out!
Sooner than we get started, you may wish to acquire and print the FREE PLANS by clicking HERE!
The 1st step to setting up this console is to create the sphere. We used 3/4” hardwood plywood ripped to 12” each to create ours. The underside of the cabinet has 3/4” pocket holes on each end. Join this shelf 3.5” from the underside of the two aspect boards using picket glue and 1.25” pocket hole screws. Make sure that to moreover add 3/4” pocket holes to the very best and contained in the aspect boards as correctly. We’ll use these to attach the very best in a later step.
Now assemble the face physique. Add 3/4” pocket holes to the ends of every of your vertical gadgets. Join them to the horizontal gadgets using picket glue and 1.25” pocket hole screws. The underside horizontal board will overhang 3/4” on both facet.
Now join the face physique to the sphere Add a line of picket glue to entrance of the sphere and line the face physique up flush. Join the physique using 1.25” brad nails into the sphere. The underside board could have a 3/4” overhang on both facet.
Now join the two aspect base gadgets. These are attached using picket glue and 1.25″ brad nails.
Assemble the middle divider by attaching the 1×3 board to the doorway of the plywood piece using picket glue and brad nails. Then, join the plywood to the underside of the cabinet using picket glue and 1.25” pocket hole screws. Don’t neglect in order so as to add pocket holes to the very best of this plywood piece as correctly. These could even be used to attach the very best piece.
We added cupboards to our cabinet subsequent. These are fully elective, and they’re usually positioned in the best place to suit your storage desires. Merely join each shelf to the center divider and the pores and skin board using picket glue and 1.25” pocket hole screws.
Subsequent join the very best. We used a laminated enterprise panel for our excessive and reduce it to measurement. Join the very best by using 1.25” pocket hole screws by the underside cabinet and into the very best.
The once more of this cabinet is 1/4” hardwood plywood. Decrease it to measurement and fasten it to the once more of the cabinet using staples or brad nails and picket glue.
Time for doorways! That is the higher half on this cabinet! These are 1/2” hardwood plywood panels reduce to measurement. Then, we used 1/4” x 2” pine craft boards to wrap the sides of the doorway. Join the trim boards using picket glue and 1/2” pin nails or brad nails.
At this degree you presumably can have gratifying with it! You could add trim to the very best and bottom to fancy it up a bit. We used two fully different types of base on the underside and excessive. For the very best trim, we flipped a base board the mistaken manner up and butted it to the very best of the cabinet.
To create the attractive doorways, we found basically essentially the most great and low-cost ceiling medallions on Amazon. You may discover them by clicking HERE! We glued them to the center of the door and used some brad nails to hold it in place until it dried. The holes merely fill will picket filler.
CLICK HERE for the prolonged bar pulls we used on the doorways!
And, CLICK HERE for a hyperlink to the hinges!
Thanks quite a bit for stopping by guys! Inform us you in all probability have any questions the least bit and HAPPY BUILDING! Proper right here’s just some further photos of her!
