Hey guys! I simply these days constructed a sweet pal of mine a model new consuming desk for her consuming house. She’s a foster mama and he or she wanted a large desk to seat her family and likewise her infants when she has them residence collectively together with her. This was such a fulfilling problem and I like the best way it turned out in her home. Among the best issue about this desk is that it makes use of 19 2 x 6 boards. That’s it! No completely different lumber is required and the result’s just so cute! You could get the free plans on the bottom of this submit and I’ll stroll you via all of the assemble proper right here. First, look how cute it turned out in her kitchen!
The first step to establishing this desk is creating the desk prime. These are 2×6 boards that we ripped down to 5”. I used my new Kreg Jig 720Pro in order so as to add 1.5” pocket hole screws down one prolonged side of all nonetheless 1 of the plank boards, and likewise on the ends of each plank board. They’re such a perfect step up from the sooner Kreg Jig K4 model. You’ll uncover it HERE on Amazon!
Join the plank boards collectively first using 2.5” pocket hole screws.
As quickly as all plank boards are linked, line up the boards on each end and mark the exact measurement of the breadboards. Join the breadboards using 2.5” pocket hole screws.
Subsequent, create the leg gadgets. These are 2 x 6 boards that I ripped down to 5” massive each. Decrease to the correct dimension, and guarantee each end is decrease at a ten° angle. Add 1.5” pocket holes on one end of 1 board. The pocket holes will probably be on the inside and prime of each leg, so keep in mind to connect each leg appropriately.
Glue these boards collectively and tightly clamp them until they’re set and dry. Each leg will use two boards and you need to have 4 legs entire.
Whereas the legs are drying, assemble the best horizontal helps for the leg gadgets. These are moreover 2 x 6 boards which have been ripped to 5” inches massive each. Decrease each to dimension and laminate them collectively using wood glue and clamps with all ends flush. I moreover added wood screws through the best boards and into the underside boards on this half because of it’ll be coated by the desk prime.
You may have two laminated horizontal gadgets, one for each leg assembly.
As quickly as the whole boards are dry, join the legs to the horizontal assist boards. Join them through the pocket holes on each leg and into the horizontal assist boards using wood glue and a pair of.5” pocket hole screws. You can also drive prolonged 4” wood screws through the best of the horizontal boards and into each leg for added assist.
Now decrease and assemble the underside horizontal leg helps. These are moreover 2 x 6 boards ripped to 5” massive each. Decrease each to dimension and add 1.5” pocket holes to the underside longer boards. Each end is decrease at a 10º angle. Glue the best board to the underside board and repair using 2 1/2 inch wood screws through the underside board and into the best board.
Join the horizontal helps to the inside of each leg assembly using wood glue and a pair of 1/2 inch pocket hole screws. These will line up 4 inches from the underside of each leg.
At this degree, you are in a position to create and repair your X gadgets that may sit inside each leg assembly. Each of the X gadgets are decrease with a 2 x 6 board which have been ripped to 4” massive each. I did not add measurements or angles on this half, because of the only and most interesting method I’ve found to get appropriate cuts is to place out every bit and mark cuts with a pencil and decrease as you go. That’s exactly how I constructed every leg assemblies. I linked each half with wood glue, 2 inch finish nails, and likewise added wood screws the place I’d cowl them in order so as to add additional assist.
As quickly as every leg assemblies are full, it’s time in order so as to add the runners. The runners are 2 x 6 boards which have been ripped to 5” massive each. Decrease three runners all at 59” massive. First, join the best base runner using 2 1/2” pocket hole screws and wood glue through 1.5” pocket holes on the tip of each runner. Be certain that your pocket holes face down.
Subsequent, join the underside base runner using wood glue and a pair of 1/2” pocket hole screws through the 1.5” pocket holes on the runner and into each leg assembly. Moreover add wood glue in between these two runners and protected them using 2 1/2” wood screws through the underside runner and into the best runner.
Lastly, add the ultimate runner which might join on the prime of each leg assembly. Join it to the leg assemblies using 2.5” pocket hole screws and wood glue through the 1.5” pocket holes on the tip of the runner.
The final word step is attaching the desk prime to the desk base. There’ll probably be a 2 1/2” overhang on the longer sides of the desk and there’ll probably be a 7 1/2” overhang on each end. I like in order so as to add my finish and switch it into the house sooner than together with the desk prime to make it less complicated to maneuver. Join the desk prime through the best of the leg assemblies using 4” wood screws and likewise through the middle runner using 2” wood screws.
I stained all of the desk with Varathane Darkish Walnut wood stain. I like the best way it turned out!
Seize the FREE PLANS FOR THIS TABLE HERE!!
Do not use glue on this half do you have to plan to take the desk apart and switch it eventually. Ensure you share your builds with us on social media and #shanty2chic so we’re in a position to share!
